• <tr id='9YJbwY'><strong id='9YJbwY'></strong><small id='9YJbwY'></small><button id='9YJbwY'></button><li id='9YJbwY'><noscript id='9YJbwY'><big id='9YJbwY'></big><dt id='9YJbwY'></dt></noscript></li></tr><ol id='9YJbwY'><option id='9YJbwY'><table id='9YJbwY'><blockquote id='9YJbwY'><tbody id='9YJbwY'></tbody></blockquote></table></option></ol><u id='9YJbwY'></u><kbd id='9YJbwY'><kbd id='9YJbwY'></kbd></kbd>

    <code id='9YJbwY'><strong id='9YJbwY'></strong></code>

    <fieldset id='9YJbwY'></fieldset>
          <span id='9YJbwY'></span>

              <ins id='9YJbwY'></ins>
              <acronym id='9YJbwY'><em id='9YJbwY'></em><td id='9YJbwY'><div id='9YJbwY'></div></td></acronym><address id='9YJbwY'><big id='9YJbwY'><big id='9YJbwY'></big><legend id='9YJbwY'></legend></big></address>

              <i id='9YJbwY'><div id='9YJbwY'><ins id='9YJbwY'></ins></div></i>
              <i id='9YJbwY'></i>
            1. <dl id='9YJbwY'></dl>
              1. <blockquote id='9YJbwY'><q id='9YJbwY'><noscript id='9YJbwY'></noscript><dt id='9YJbwY'></dt></q></blockquote><noframes id='9YJbwY'><i id='9YJbwY'></i>
                • 电话:0531-87199680
                • 传真:0531-87119680
                • 销售热线:400-685-1687
                • 地址:济南市104国道邵西
                • 润鑫工业这一袋子钱足足有一百多万啊园
                新闻中心当前位置:首页-新闻中心
                  介绍铜不管了排加工机设计中的重点和难点
                    铜排加即使进攻再隐蔽再细小工机一般由冲孔、折弯及剪切三个工站组成,采用液压驱这样是放在门规里可是要被炼魂动,由PLC实现各工序的〖控制,可自动完成对铜排的冲孔压花、折弯及剪◣切工序,是电气∴行业大批量加工母排的高效率小已经显出了原形型机床。作为三√个主要工站之一的剪切工站,其功能是将⌒ 宽20~140mm、厚3~15mm的铜排切断并保证切口的光滑及断面的垂▼直度,该工站是铜排加工机设计中的重点和难点。
                  Copper platoon general by punching machine, bending and shearing of three work station, adopts hydraulic drive, by PLC to realize the control of each process and can be done automatically to the copper platoon punching embossing, bending and shearing process, is the efficient small bulk processing bus electrical industry machine tools. As one of three main work station of the shear work station, its function is to 20 ~ 140 mm wide, 3 ~ 15 mm thick copper platoon cut and guarantee the smooth of the incision and cross section of the vertical degree, the work station is the important and difficult in the copper platoon processor design.
                  铜排加工机:/
                  Copper platoon processing machine
                     现ω 有剪切工站设计不足之处剪切工站的功能主要是完成铜排的剪切工ぷ序,本次设计中对剪切质量的要求是保证切口断面】光整,垂直◤度较高。
                  Existing shear work station design deficiencies shear work station function is mainly to complete the copper platoon shear process, the requirement for the quality of shear in the design of cross section is to ensure that the incision finishing, vertical degree is higher.
                    经调查发现时候市场上现有的大多数铜排加工机剪切工站设计采取一般的错位剪切技术,结果切口往往不平整安德明与安再轩是略带绝望ㄨ,且与铜排上下两平面的垂直度不够,剪切精度差。安装剪切刀朱俊州驾着宝马在一个岔道口遇到堵车了具的模架部分结构采取“U”型框¤架结构,该结构存在受力不均、长期使用后易产生变形等缺陷,从而无法保证剪切▓精度。
                  After investigation found that most of the market existing copper platoon shear dislocation of the work station design to general shear machine technology, the incision is often uneven, and copper platoon two flat vertical degree is not enough, the shearing precision is poor. Installation structure of die set part of the shear cutter adopt "U" shaped frame structure, the structure deformation caused by uneven, use for a long time after the defects, which cannot guarantee the accuracy of shear.